New rod holder - Printable Version +- Fishing Forum (https://bigfishtackle.com/forum) +-- Forum: Float Tube Fishing (https://bigfishtackle.com/forum/forumdisplay.php?fid=396) +--- Forum: Float Tubing General (https://bigfishtackle.com/forum/forumdisplay.php?fid=81) +--- Thread: New rod holder (/showthread.php?tid=821556) |
New rod holder - albinotrout - 05-21-2013 Ok since I got my new 8 wt fly rod I found that the handle was just a little too big for the current rod holders I had made. So back to the work bench. I came up with a great design that still will be tweaked. Best thing is that it is not permanant (not glued) so I can move it around as needed. I went with a piece of ABS for the tube and PVC for the joints. I also used a dle clamp to attach it to my current workings. The next area of making it better is I am thinking of replacing the T joint with a an elbow if I can find one that would fit. Heres the pics! Now its time to go try it out. Time to FISH!!![cool] [inline "DSCN1799 - 400.jpg"] [inline "DSCN1797 - 400.jpg"] [inline "DSCN1798 - 400.jpg"] [signature] Re: [albinotrout] New rod holder - kandersonSLC - 05-21-2013 Very cool. Love the dle-clamp idea. Did you get that at Home Depot in sprinkler dept? [signature] Re: [kandersonSLC] New rod holder - albinotrout - 05-21-2013 Yes I did. Lowes has them too. [signature] Re: [albinotrout] New rod holder - flygoddess - 05-21-2013 Great idea. You might want to make the slip for the rod more narrow. The width of the reel seat. http://www.youtube.com/watch?v=xGdMwfWEw-E And if that is an End Cap on the bottom, might want to rethink that more as a drain. But you are on your way. [signature] Re: [flygoddess] New rod holder - albinotrout - 05-21-2013 I tried doing that but the rod handle was receiving damage so I had to make it just a little bit bigger. [signature] Re: [albinotrout] New rod holder - flygoddess - 05-21-2013 Damage? PVC too small? [signature] Re: [flygoddess] New rod holder - albinotrout - 05-21-2013 No not too small, rod fit nicely. Because the reel seat fit snugly the cork would scrape the edges where I cut out. I did sand down to smooth but due to the tight fit damage was trying to occur so I widened it a little. As you can see from this pic the handle rests a little funny so I had to widen it. It is still snug though with the reel on the rod. Another thought is I can always attach a piece of Velcro to the top of the tube which looks like it would push the rod back a little. As seen in the second pic. The third pic shows the handle and why I needed different materials this time. [signature] Re: [albinotrout] New rod holder - flygoddess - 05-21-2013 The handle is called a FULL WELLS and I see the fighting butt is oversized. I have a few rods that I have seen this before[] You can do the velcro as you had to go with a larger PVC tube because of the butt, or you can cut a side notch to hold the reel seat tight instead of the cork. This is the way the Scotty's are built. [signature] Re: [flygoddess] New rod holder - albinotrout - 05-21-2013 I will have to see how that design will work. Where I have the holder placed right now it is between two other rods. Another spot I thought about would be on the outside of the rack on the motor side. I gotta see how the reach is first. My arms are only so long. []. [signature] Re: [albinotrout] New rod holder - flygoddess - 05-21-2013 Great! Let me know how that works with the fly rod sticking straight up. I have always seen them staggered at an angle. 9 feet in the wind can make a mess[] [signature] Re: [flygoddess] New rod holder - albinotrout - 05-21-2013 I've done it with my other two 5 wt rods fine. They are 8'6" and 9' . The design of this holder also makes it so I can turn it at an angle if needed. I wanted this design to be able to handle many different conditions as necessary.[] [signature] Re: [albinotrout] New rod holder - flygoddess - 05-21-2013 Great Job [signature] Re: [flygoddess] New rod holder - albinotrout - 05-21-2013 Thanks! If everything works as planned with this holder I will make some more. I have a couple of reels without friends feeling lonely. A spinning reel and a 4 wt reel. [cool] [signature] Re: [albinotrout] New rod holder - albinotrout - 05-22-2013 Here is the design change with the elbow only. [signature] Re: [albinotrout] New rod holder - flygoddess - 05-22-2013 Don't forget a drain hole...it could get nasty in the elbow. [signature] Re: [flygoddess] New rod holder - albinotrout - 05-22-2013 That's true, never thought of that. [signature] |